Home / Radio / SIDs / SID_SpectrumLab_config

Spectrum Lab set-up for a 24 hour SID monitoring station

Set-up of SpectrumLab is relatively straightforward; here I will take you through the main points to consider.

Components Window

This is found under Components / Show Components
Use this window to configure the components that should be in circuit, for SID monitoring we want all the components turned off, take special note that the AGC is turned off!
SL_SID_Components.JPG

Options / Audio Settings

This is where you set the soundcard input, sample rate and bits per sample, you will have to set these to suit your soundcard capabilities, but in general you want to set the sample rate to the highest possible (half the sample rate will be the highest frequency available in the FFT display) and the bits/sample to as high as possible, the more bits per sample the larger the dynamic range (number of signal levels) you will be able to distinguish
SL_SID_audiosettings.JPG

Options / FFT Settings

Here you can set the units to record, I prefer Volts but it’s up to you. You can also adjust the amount of internal averaging, this can help provide some smoothing so reduce noise in the result.
SL_SID_fftsettings.JPG

Plotter settings

The Watch List Tab should contain a list of the frequencies you are monitoring, be careful of artefacts in the FFT appearing as channels, these can usually be detected as signals that exactly mirror (in every way) the true signal. When choosing the channels to watch use the average function (avrg(low,high)) this will introduce a little smoothing and reduce noise.
SL_SID_plotterwatchlist.JPG
On the Horizontal Tab set the scroll rate to about 20s, this does two things, it reduces the update to the plotter graph to once every 20s and also reduces the capture of data to once every 20s, this keeps the amount of data manageable and gives you a reasonable time axis on the plotter window.
SL_SID_plotterhorizontal.JPG
On the Memory, Misc Tab, set the number of channels you want to record.
SL_SID_plottermemory.JPG
On the Export Tab set the name of the file you want your data saved to and the file format
SL_SID_plotterexport.JPG

If you want to periodically save the plotter graph and upload it to a website (see SIDs page) select File / Periodic actions and enter the two lines indicated, the first line saves the plotter window in a file, the second line executes a windows batch command which will upload the file. Both these files sit in the c:\ftp_upload directory.
SL_SID_periodicActions.JPG

contents of the batchfile named c:\ftp_up.bat
:: Batchfile to upload a screenshot to a website via FTP.
:: Called from some 'Spectrum Lab Grabber' applications.
:: Uses the command line driven FTP client in MS windows.
:: Only works when located in C:\ftp_upload\ftp_up.bat .
:: Doesn't require any 3rd-party software !
:: You will need to modify your provider's ftp host name,
:: your user name, and (unfortunately non-encrypted)
:: the FTP password in the 'ftpcmd' lines further below .
:: The name of the file to be sent is specified as argument %1
:: when this batchfile is invoked (from SL's periodic actions, etc)
::
:: Make sure we are where we should be (current directory) :
cd \ftp_upload
::
:: Create the input (command file) for the ftp client program .
:: The line after the USER command is the password .
> ftpcmd.txt ECHO USER replacewithyourFTPusername
>> ftpcmd.txt ECHO replacewithyourFTPpassword
:: >> ftpcmd.txt ECHO cd grabber
>> ftpcmd.txt ECHO binary
>> ftpcmd.txt ECHO put %1
>> ftpcmd.txt ECHO disconnect
>> ftpcmd.txt ECHO bye
::
:: At this point, we have created a temporary command file
:: for the FTP client. This comman file replaces the input
:: which would be entered via keyboard in an INTERACTIVE ftp session .
:: Now start the ftp client program, output redirected to a file
:: which is EXTREMELY helpful for troubleshooting .
:: Replace the dummy address with your provider's ftp address:
FTP -n -s:ftpcmd.txt ftp.btinternet.com > ftplog.txt
:: The -n option suppresses the auto-login upon initial connection .
:: The -s option specifies a text file with FTP commands .
:: If the FTP client (above) fails, TEST EACH STEP IN INTERACTIVE MODE !
:: (each step is now in



Copyright © 2005-2017 Crayford Manor House Astronomical Society Dartford, Kent.Registered Charity Number 1156678. All rights reserved. No part of this website may be reproduced.
Page edited 2 times. Last edit by - SimonTelescopium SimonTelescopium on Jul 19, 2011 1:02 pm. This site contains 560 pages
CMHASD - SID_SpectrumLab_config